|
#688952
Wed Jun 21 2017 10:38 AM
|
Joined: Oct 2016
Posts: 66
Active Member
|
OP
Active Member
Joined: Oct 2016
Posts: 66 |
I was double checking the placement of the signs on the front panel. The previous holes on mine I had repaired since they did not align with with my signs but assume the general placement is correct?
Vintage car restorer/collector with a love for all things old.. Too many toys never enough room.
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
|
Joined: Feb 2003
Posts: 2,457 Likes: 24
Veteran Member
|
Veteran Member
Joined: Feb 2003
Posts: 2,457 Likes: 24 |
Your placement seems too high to me? I think the pump plates should be lower. I usually measure up from the bottom in odd numbers until I find the correct look. Try 9" then 11" then 13" or more. I think you will find the pump looks better if the signs are lower. Paul www.severngaspumps.com
|
|
|
|
Joined: Dec 2002
Posts: 3,188 Likes: 1
Veteran Member
|
Veteran Member
Joined: Dec 2002
Posts: 3,188 Likes: 1 |
Paul -Just curious here-Why odd numbers?
|
|
|
|
Joined: Nov 2000
Posts: 7,791 Likes: 9
Veteran Member
|
Veteran Member
Joined: Nov 2000
Posts: 7,791 Likes: 9 |
These signs have been repro, which of the signs above our original or which are repros?
Jack Sim
Author, 1st & 2nd editions of Gas Pump ID book, 3rd edition is now available at www.gaspumpbible.comAir Meter ID book also available
|
|
|
|
Joined: Oct 2016
Posts: 66
Active Member
|
OP
Active Member
Joined: Oct 2016
Posts: 66 |
Your placement seems too high to me? I think the pump plates should be lower. I usually measure up from the bottom in odd numbers until I find the correct look. Try 9" then 11" then 13" or more. I think you will find the pump looks better if the signs are lower. Paul www.severngaspumps.com I thought so too but measured placement on other pumps that "looked" original like the one posted and it is pretty darn close. You can kind of see where my original holes were on this backside photo. may be a hair lower. May be the angle I took the original picture also.
Last edited by chevy350; Wed Jun 21 2017 11:01 PM.
Vintage car restorer/collector with a love for all things old.. Too many toys never enough room.
|
|
|
|
Joined: Oct 2016
Posts: 66
Active Member
|
OP
Active Member
Joined: Oct 2016
Posts: 66 |
These signs have been repro, which of the signs above our original or which are repros?
Jack Sim It would be nice to have a set of originals... but boy they are not cheap.. Repros on this are fine for me.
Vintage car restorer/collector with a love for all things old.. Too many toys never enough room.
|
|
|
|
Joined: Feb 2003
Posts: 2,457 Likes: 24
Veteran Member
|
Veteran Member
Joined: Feb 2003
Posts: 2,457 Likes: 24 |
Paul -Just curious here-Why odd numbers? Jim, Over the years, I have measured original sign locations from the pumps restored. Just about all used odd numbers up from the bottom. I don't know why but they did? Since it worked for all these folks who came before me, I adopted the method. Check out all the pumps we have restored and you will see where we located the signage using this method. Regards, Paul www.severngaspumps.com
|
|
|
|
|
|