|
|
#217790
Wed Dec 08 2010 05:09 PM
|
Joined: Jan 2009
Posts: 5,980 Likes: 24
Veteran Member
|
OP
Veteran Member
Joined: Jan 2009
Posts: 5,980 Likes: 24 |
I need the piece or casting that would bolt onto the side of the pump where the sight glass comes out. Looks like there are two holes in it but have not picture or part to see. There is also a hole at the top of one of the castings or head piece in which something was either attached or came out of.Also what nozzles would work for this pump or what came with it?
Thanks
Craig
|
|
|
|
|
Joined: Oct 2003
Posts: 1,664 Likes: 25
Veteran Member
|
|
Veteran Member
Joined: Oct 2003
Posts: 1,664 Likes: 25 |
i hav a bennett 150 & i think there are jst bolts or screws that hold the sheetmetal on in those 2 holes. are you sure thats a rheem?? mine has the same top also<, spot is probably for a pricer? chris
|
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
Bennett merged w/ Rheem,
Wayne merged w/ Boyle Dayton,
Tok/Nat. opened a plant in the Frisco Bay area.
|
|
|
|
|
Joined: Jan 2009
Posts: 5,980 Likes: 24
Veteran Member
|
|
OP
Veteran Member
Joined: Jan 2009
Posts: 5,980 Likes: 24 |
Ron Scobie mentioned that there were some cast pieces up there, hopefully Ron is watching this column and can also see this picture. My faces said Rheem Service station equiptment on them.
Craig
|
|
|
|
|
Joined: Oct 2000
Posts: 22,780 Likes: 5
Veteran Member
|
|
Veteran Member
Joined: Oct 2000
Posts: 22,780 Likes: 5 |
According to the RHEEM SSE pump @ local museum, no casting was used around Visi pipe.
I would think if a pricer was used it would be opposite the visi, not above visi.
|
|
|
|
|
Joined: Dec 2000
Posts: 1,730 Likes: 19
Veteran Member
|
|
Veteran Member
Joined: Dec 2000
Posts: 1,730 Likes: 19 |
Dick is correct. The styles with the pipe lower on the side have covers.
Ron
|
|
|
|
|
Joined: Jan 2006
Posts: 377 Likes: 2
Petro Enthusiast
|
|
Petro Enthusiast
Joined: Jan 2006
Posts: 377 Likes: 2 |
Craig my rheem bennett shows that its a vent pipe that comes up from an air eliminator a enclosed couple picturs -- Also mine has the two holes with nothing in them and doesn't seem to have ever been anything there and my vent pipe is on the oposite side of the viso gauge hope this helps Laroy
Last edited by pasngas; Thu Dec 09 2010 05:04 PM.
|
|
|
|
|
Joined: Jan 2009
Posts: 5,980 Likes: 24
Veteran Member
|
|
OP
Veteran Member
Joined: Jan 2009
Posts: 5,980 Likes: 24 |
Thanks for all the pictures and guides. I now see that the piece that went in the hole is what I have as a spare part. Just did not know where it went. As for the bezels that I was thinking went on the sight glass pipe, well it just would have looked better I guess but what the heck.
Thanks to all
Craig
|
|
|
|
|
|
|
