|
|
 reliding oil can flat
|
Joined: Nov 2012
Posts: 283
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Nov 2012
Posts: 283 |
I'm looking for someone who is able to take an oil can that has been flattened and reroll and lid it. Is anybody out there doing this?
thanks
Jake
Always looking for Veedol and Tydol cans and signs
|
|
|
Please - NO offers to Buy or Sell in this forum category
Statements such as, "I'm thinking about selling this." are considered an offer to sell.
|
|
 Re: reliding oil can flat
|
Joined: Dec 2002
Posts: 3,188 Likes: 1
Veteran Member
|
|
Veteran Member
Joined: Dec 2002
Posts: 3,188 Likes: 1 |
Sent you a PM with someones contact info.
|
|
|
Re: reliding oil can flat
|
Joined: Sep 2008
Posts: 1,749
Veteran Member
|
|
Veteran Member
Joined: Sep 2008
Posts: 1,749 |
I would be interested in seeing this done myself .
see ya on the road folks !
|
|
|
Re: reliding oil can flat
|
Joined: Sep 2012
Posts: 2,194
Veteran Member
|
|
Veteran Member
Joined: Sep 2012
Posts: 2,194 |
Done quite a few of them lately.
Dan
Quart and Liter can relidding and dent removal services.PM for detail and pricing.
Collecting Mobil and other graphic quart cans.
|
|
|
Re: reliding oil can flat
|
Joined: Nov 2001
Posts: 1,878 Likes: 42
Veteran Member
|
Veteran Member
Joined: Nov 2001
Posts: 1,878 Likes: 42 |
|
|
|
Re: reliding oil can flat
|
Joined: Nov 2012
Posts: 283
Petro Enthusiast
|
|
OP
Petro Enthusiast
Joined: Nov 2012
Posts: 283 |
This is what I have to start with. Couldn't pass up this can in any form!
Always looking for Veedol and Tydol cans and signs
|
|
|
Re: reliding oil can flat
|
Joined: Nov 2000
Posts: 7,791 Likes: 6
Veteran Member
|
|
Veteran Member
Joined: Nov 2000
Posts: 7,791 Likes: 6 |
Years ago Dick Bennett was the guy who you sent your cans to, to be either re-lid, or restored. He was the guy, but unfortunately he is not with us anymore.
I am pretty sure I know who purchased all his equipment to do this service, but I have not seen where this person has announced his desire to again offer this service. Why this person bought all this equipment and not used it is beyond me.
After the death of DB his assets were sold out to a few people. There was no auction. Where all the gas pumps, etc. went I truly don't know.
While I was truly surprised at learning of the death of DB, I have always wondered where his great deal of pumps, etc. went to.
Jack Sim
Author, 1st & 2nd editions of Gas Pump ID book, 3rd edition is now available at www.gaspumpbible.comAir Meter ID book also available
|
|
|
Re: reliding oil can flat
|
Joined: Jul 2012
Posts: 1,145 Likes: 1
Veteran Member
|
|
Veteran Member
Joined: Jul 2012
Posts: 1,145 Likes: 1 |
junior25 on here daryl leatherdale is excellent at this pm for his number if you wish .
Follow the Red Indian Trail
|
|
|
Re: reliding oil can flat
|
Joined: Jul 2013
Posts: 37
Active Member
|
|
Active Member
Joined: Jul 2013
Posts: 37 |
I have some cans that need re lid. Is there any way you could send me Darryl’s phone number? Thanks in advance!
|
|
|
Re: reliding oil can flat
|
Joined: Nov 2009
Posts: 480 Likes: 16
Petro Enthusiast
|
|
Petro Enthusiast
Joined: Nov 2009
Posts: 480 Likes: 16 |
That is a good one to do for the outer edge of the lids are still attached to the top and bottom ends. A lot of times someone uses a regular can opener which cuts this off and shortens the quart. Also if there is still metal remaining on the backside around the hole it can be knocked back with a little bit of patience to fill in the hole. Cheers, Don.
|
|
|
|
|
|
|
