|
#612889
Wed May 13 2015 05:10 AM
|
Joined: Sep 2012
Posts: 305
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Sep 2012
Posts: 305 |
Not looking for anything for restoration, this is an outside pump that im piecing together. Let me know what ya'll have
-Brian _________________________________________________ Collecting Skelly Globes,Signs, & Tins / Chevrolet/GM Signs,Cans, & Tins
|
|
|
|
Joined: Dec 2005
Posts: 806 Likes: 8
Petro Enthusiast
|
Petro Enthusiast
Joined: Dec 2005
Posts: 806 Likes: 8 |
How many and what style/length do you need? I have a stack of rods. Also have a super nice set of red patina 615 skins if needed. I will be at Iowa Gas.
Coryell 70/Nebraska items wanted
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
I might have an old jar lid out at the farm. I'll try get a look today.
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Sep 2012
Posts: 305
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Sep 2012
Posts: 305 |
Sorry guys but I have never really been in depth on a visible pump yet. I also don't have the pump in my possession yet, going to pick it up in a couple weeks. I know they aren't rocket science but im not sure on length on the rods? I guess I know there are different lengths now. I know the top hat is coming with it and from the bottom cylinder base down is pretty much all there. So from what research iv done so far ill need a jar lid for the top hat to mount to and the rods to mount to
Thanks guys. I attached a picture of what he sent me so that's all I have to go by. Lantern obviously not included
Last edited by LSx; Wed May 13 2015 08:41 AM.
-Brian _________________________________________________ Collecting Skelly Globes,Signs, & Tins / Chevrolet/GM Signs,Cans, & Tins
|
|
|
|
Joined: Oct 2007
Posts: 12,282 Likes: 12
Veteran Member
|
Veteran Member
Joined: Oct 2007
Posts: 12,282 Likes: 12 |
Found a jar lid for you. It doesn't have the glass inspection cover on it and I don't think I have any extras? The rods for Wayne visibles are all the same and you will need nine of them that are 27 inches long. They have a short threaded area on one end where they screw into the base and have a long threaded area on the other end, so that there can be a nut on each side of the jar lid. You should try and get the original nuts for the rods too, as they look a little different from modern ones. You will need a glass cylinder that measures 12 1/2 by 26. You'll probably need a set of gallon markers too.
Last edited by K W FRITH; Thu May 14 2015 11:44 AM.
Everything Cities Service Specializing in old Gas Pumps kwfrith@gondtc.com Cell#-701-739-6133
|
|
|
|
Joined: Sep 2012
Posts: 305
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Sep 2012
Posts: 305 |
-Brian _________________________________________________ Collecting Skelly Globes,Signs, & Tins / Chevrolet/GM Signs,Cans, & Tins
|
|
|
|
Joined: Sep 2012
Posts: 305
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Sep 2012
Posts: 305 |
-Brian _________________________________________________ Collecting Skelly Globes,Signs, & Tins / Chevrolet/GM Signs,Cans, & Tins
|
|
|
|
Joined: Sep 2012
Posts: 305
Petro Enthusiast
|
OP
Petro Enthusiast
Joined: Sep 2012
Posts: 305 |
Got the pump home, jar lid from Kevin was at the front door when I got home.
Now I just need rods! Let me know what yall have
-Brian _________________________________________________ Collecting Skelly Globes,Signs, & Tins / Chevrolet/GM Signs,Cans, & Tins
|
|
|
|
|
|